FREE Tutorial - Bracelet «NATALIE» Designed By Yuliya Abelovich

This «NATALIE» bracelet pattern was developed by Yuliya Abelovich.
Unauthorized copying, distribution, selling and teaching of this tutorial or parts of this tutorial are prohibited.
You are welcome to sell the finished product from the tutorial you have purchased in small amounts (mass production is prohibited).
Please, respect the copyright.

Find more tutorials here.

The length of one link of the bracelet is 0.8 cm. You can make any length by adding or reducing the number of links.

Materials required (for A – pink bracelet, B – lavender bracelet):

• Czech Glass Two-Hole Tile Beads ESTRELA Square 6x6 (A- Light Pink, one side pearl coating; B -  Violet, one side pearl coating), 1 pcs for each link in bracelet - Click here
• Es-O beads 5 mm (A - Alabaster Powder Pale Pink, B - Alabaster Powder Light Purple) – 4 pcs for each link in bracelet + 2 pcs - Click here
• Pearls (or round beads) 3 mm (A – white, B – purple, lilac or dark blue color) – 4 pcs - Click here
• Pearls 6 mm (A – white, B – dark blue color) – 2 pcs for each link in the bracelet - Click here
• Seed beads Miyuki 15/0 (for two colors - gold plated  #191) – 1 gram (also may use Czech seed beads 15/0) - Click here
• Fireline 6 lb for bracelet (0.3 m + 0.13*long of bracelet) For example, if bracelet 16 cm, you need 0.3 + 0.13*16 = 2.38 m fireline - Click here
• Two beading needles – size 12 - Click here
• Bracelet lock and two jump rings for the lock - Click here
  
• Small pliers for jewelry making - Click here

1. Put on two needles on the ends of one thread.

2. Take on the left needle Es-O, seed bead 15/0, Es-O, seed bead 15/0, Es-O, Tile, Es-O, seed bead 15/0, Es-O, seed bead 15/0, Es-O in order, as picture shows.

3. The right needle goes through the higher hole of Tile.

4. The left needle goes through the higher hole of Tile and goes out through Es-O bead.

5. The left needle goes through the lower hole of the left Es-O bead, as picture shows. Now align the ends of the thread. You may to move beads to the right or left. The two ends of the thread must be the same length.

6. The right needle goes through the higher hole of Es-O, inserts Tile.

7. The left needle goes through beads, the way as picture shows.

8. Take on the right needle seed bead 15/0, Es-O, seed bead 15/0, Es-O. Take on the left needle seed bead 15/0, Es-O, seed bead 15/0, Es-O.

9. The right needle goes through the higher hole of Tile bead. Repeat inserting beads, as steps 4-9 show all the length of the bracelet.

10. When you finish, after step 5 right needle goes through Es-O bead and the left needle goes through Es-O bead.

11. Take on the right needle 6 seed beads 15/0 and go out through Es-O, as picture shows.

12. Another needle also goes through 6 seed beads 15/0 and goes out through Es-O on the right side.

13. Right needle inserts Pearl 3 mm between Es-O beads.

14. Insert Pearl 6 mm between next Es-O. Repeat inserting Pearls 6 mm all the right sidelong. After this insert beads, steps 13-14 shown on the left side of the bracelet.

15. When you finish, insert last Pearl 3 mm on the right side and insert last Pearl 3 mm on the left side.

16. Take on the right needle 6 seed beads 15/0 and go out through Es-O on the left side.

17. Spend both needles on weaving. The ends of the thread can be tied into knots in bead weaving. After this, you may pass them through the weaving, tie one more time, and hide the ends of the thread, cut off the ends.

18. With pliers unplug the rings (rings open with a sideways movement, as you see on the photo), and put them on the locks for the bracelet. Put the rings on the bracelet and again close them.

Enjoy the tutorial? Support Yuliya, subscribe to the Facebook page here